MassimoPL77 Posted October 16, 2017 Report Share Posted October 16, 2017 Hi! I'm an italian amateur guitar builder. I started this hobby three years ago and I recently finished my 8th build. As I posted the pictures of the guitar on the "guitar of the month" contest, I decided to open a thread here to publish all the photos taken during the building process. For this Les Paul build I followed the plans made by John Catto, but I didn't want to build a real replica: I respected all the original sizes and the top carving, but woods and some building choices were customized. To start I prepared all the templates Then I glued two pieces of ash from the same board, and i cut the body leaving some space for refinishing it with a router. Next step was to route the channel for the wiring and, on the other side, the cavities for the pots and the toggle switch Now it's time to see how much this piece of ash weights This is really too much! A finished guitar would be near to 6kgs! So I decided to route a large weight relief chamber. This is the template And this is the result after the shock diet! Near to 1kg less! Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 16, 2017 Author Report Share Posted October 16, 2017 I wanted a dark wood for the top, because I like the contrast between the top and the body, so I found this asian ebony, really similar to Makassar, which was very figured and enough thick to be a Les Paul top (16mm). Firstly I glued the two parts together: Then I glued together top and body using my vacuum pump. To be sure that the wood doesn't move I tightened two screws on the pickup positions. I've bought this pump to glue veneers, but I had really good results also with thicker woods and now I wouldn't go back for clamps! Here is the result after routing the sides: the glue line is almost invisible. 1 Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 16, 2017 Author Report Share Posted October 16, 2017 Before starting to carve the top I routed the back contour with a 5mm concave bit. Now I'm ready to start with the top. Firstly, using seven templates I route the lines on the top. I work with an arm router, so I have to doubletape the templates on the back of the guitar. Then I had to route the neck plane and the pickups plane. To do it I made a simple jig: an MDF board with two screws, which gives a great control of the angle. Using this it was easy to set up the right angle. 4.2° for the neck plane: 1.4° for the pickup plane In this last photo you can see the three different angles on the top Now it was time to start carving the top. My tools were a sander, some small scrapers and a lot of sandpaper. This ebony is really tough, so I needed some hours of hard work to reach this result: After another session of carving and sanding i was really near to the final result. I also made the covers with the same wood of the body. I was lucky enough to find some pieces of wood which match the grain of the body. The top is not perfectly book matched, but the most different part near the neck pocket will be covered by the fretboard and the neck pickup. I don't like to see screws on wood covers, so I opted for some small but powerful neodymium magnets to keep all the covers in their positions. Quote Link to comment Share on other sites More sharing options...
Popular Post MassimoPL77 Posted October 17, 2017 Author Popular Post Report Share Posted October 17, 2017 Next steps were binding and purflings. To cut the channels with the arm router was an easy task The most difficult part was to cut the channel on the cutaway, because in that position the channel doesn't lay on a plane, but it goes up after the horn and then goes down near to the neck pocket. To achieve it I used this jig with my Makita hand router The channel wasn't perfect, because the radius was too narrow for the jig to work correctly, but after some refining with a chisel it was acceptable. My aim was to do a flamed maple binding and a four parts purfling: ebony/golden mop/ebony/maple. Instead of using Zipflex for the central purfling, I decided to do it the old way, using teflon strips and then filling the resulting channel with mother of pearl strips. This is what I wanted to achieve: First of all I prepared the binding: I cut the maple 1.5mm thick and 6mm large, then I glued a subtle strip of ebony under, so I could have a black purling line between the maple binding and the ash body Now it was time to glue the purflings, using the teflon strip instead of mother of pearl. Teflon doesn't stick with glue, so later it could be easily removed. Then I glued the binding and when the glue was dry I removed the teflon strip. In the next photo It's possible to see the void channel left by the teflon strips and the golden mother of pearl strips that I used to fill it. As I pressed the strips inside the channel, they break in smaller pieces, so they could adapt to all the curves of the guitar: I only had to cut to perfect size the portion on the horn, because there the radius was too narrow to achieve a good result with this technique. Once inserted in the channel, I glued in position the strips with thin ca glue. Now I only had to sand everything flush. The process was long and tricky but I was really happy with the result! 5 1 Quote Link to comment Share on other sites More sharing options...
Norris Posted October 17, 2017 Report Share Posted October 17, 2017 Welcome and thanks for posting. That's some beautiful work and an excellent result! Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 17, 2017 Author Report Share Posted October 17, 2017 6 hours ago, Norris said: Welcome and thanks for posting. That's some beautiful work and an excellent result! Thanks Norris! I'm a member of this community since 2014, but up to now I was only lurking for infos and admiring the work of others. Only now I've found courage to contribute. Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 17, 2017 Author Report Share Posted October 17, 2017 The neck is the part of the guitar that differs the most from the traditional Les Paul: I made a 5 parts laminated neck with a 15°scarf joint and a volute. To start I glued together the sandwich: ebony /maple/ebony/maple/ebony. The ebony is the same asian wood used for the top. (Sorry for the low quality of the next photos : I don't have pictures of the building process of the neck for this guitar, so I'm using some pictures of an older build made with the same woods) This is the result after planing: To cut the scarf joint I used the table saw with this jig: I clamped the neck blank to the jig which is 15° angled to the blade: After planing it was time to glue the two parts together. Between the two parts of the neck I glued a thin board of maple; once carved, this board will take the look of an arrow. To glue everything together I used five clamps: two clamps to keep in position the two parts of the neck, the others to put pressure on the joint. This is the result after planing: And this is the "arrow": Now let's go back to the photos of the Les Paul! To make the heel I cut a portion of the neck and I glued on it, then I cut the tenon. With my equipment it was easier for me to make an angled tenon, while the neck pocket is flat. I think I nailed the neck and body joint And this is the joint after trimming the neck: Here is a photo of the routed headstock. Later I will glue a 2mm ebony head plate on it. And finally two shots of the guitar: 4 Quote Link to comment Share on other sites More sharing options...
Popular Post MassimoPL77 Posted October 18, 2017 Author Popular Post Report Share Posted October 18, 2017 For this guitar I wanted to do an intricate inlay and I choose one of my favourite subjects: roses. I started making inlays three years ago and it was immediately love with this technique. Most often I do small subjects like logos or writings, so this one is my second full fretboard inlayed. On the twelfth fret I decided to inlay a small ladybug (from which the name of the guitar) to vary a little and to create a colorful subject that stood out on the rest of the inlay. The drawing of the layout is always the most demanding part: I draw by hand, first looking for subjects, then marking them out with a pencil and finally creating the composition. This is a photo of an intermediate phase: frets 1-9 The final result is really similar to those drawing for children to fill with coloured pens When I have the final layout I cut all small pieces gluing them to mop, abalone, recon stones... and I start cutting with a jeweler saw. Here is the ladybug: red recon stone, ebony and white mother of pearl. She has no legs, cause they will be cut on the "leaf" where she will lay and later filled with epoxy mixed to ebony dust. Now the work is really repetitive: cut the piece, glue to mop, cut the mop, file blurry edges and start again. Sometimes pieces are really small! When I finish to cut all the pieces for a subject I glue them together, being careful non to leave gaps between the pieces. In the end this is the final result: approximately 250 tiles. Now is time to route the fretboard and inlay everything: to do it I use a Dremel with an aluminum base. All parts are glued with epoxy mixed to ebony dust which at the same time serves as glue and filler. This required near to 100 hours to complete. Cutting frets on this fretboard was really stressful! I don't have photos for next steps, but I bound the fretboard with the same flamed maple used for the body binding, I installed the frets and finally glued the fretboard on the neck. 6 Quote Link to comment Share on other sites More sharing options...
ScottR Posted October 18, 2017 Report Share Posted October 18, 2017 That much inlay makes my fingers hurt and my eyes twitch just thinking about it. You are a patient man. And a gifted one as well. Beautiful work! SR Quote Link to comment Share on other sites More sharing options...
Zoltar Posted October 18, 2017 Report Share Posted October 18, 2017 Wow, and to think I've been worried about inlaying dots neatly That's stunning Massimo, I'm not surprised it took a while. I often look at guitar makers' work and think that they'd be excellent furniture makers. I reckon that you'd be great at silversmithing too! Quote Link to comment Share on other sites More sharing options...
Norris Posted October 19, 2017 Report Share Posted October 19, 2017 Wow! That's a fabulous inlay and a great demonstration of patience Quote Link to comment Share on other sites More sharing options...
Skyjerk Posted October 19, 2017 Report Share Posted October 19, 2017 WOW! Massimo, I am speechless. Your work is awesome! Your inlays are absolutely beautiful. I do my own inlaying, but have chickened out and paid someone else to actually cut the shell for me (except for some more simple pieces). I wish I had your patience Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 19, 2017 Author Report Share Posted October 19, 2017 On 18 ottobre 2017 at 8:00 PM, ScottR said: That much inlay makes my fingers hurt and my eyes twitch just thinking about it. You are a patient man. And a gifted one as well. Beautiful work! SR Thank you Scott! But, as you can imagine, the real patient in the house is my wife! 23 hours ago, Zoltar said: Wow, and to think I've been worried about inlaying dots neatly That's stunning Massimo, I'm not surprised it took a while. I often look at guitar makers' work and think that they'd be excellent furniture makers. I reckon that you'd be great at silversmithing too! Thanks Zoltar! My father is a furniture maker. I followed a different path in life (I'm a teacher) but I've inherited the passion for woodworking. 8 hours ago, Norris said: Wow! That's a fabulous inlay and a great demonstration of patience Thank you Norris! 3 hours ago, Skyjerk said: WOW! Massimo, I am speechless. Your work is awesome! Your inlays are absolutely beautiful. I do my own inlaying, but have chickened out and paid someone else to actually cut the shell for me (except for some more simple pieces). I wish I had your patience Thanks Skyjerk. As I started inlaying I felt immediately in love with this technique. For me it's so satisfying to work with mother of pearl and I'm always surprised by its changing colours and the different effects that you can achieve! Quote Link to comment Share on other sites More sharing options...
Popular Post MassimoPL77 Posted October 19, 2017 Author Popular Post Report Share Posted October 19, 2017 I decided to put a rose also on the headstock, to complement the inlay on the fretboard. This drawing is smaller than the others, because the flower has to go between the machine heads. I decided to inlay on the headstock also a drawing: the logo Delky. It's just a joke from school times, a nickname from my surname Del Col. The leaves are made with abalone paua, the petals are made with white mop and australian greenlip abalone. The contrast between the different colours of the shells helped me to give more depth to the rose. The writing is made with golden mop. As you can see on the picture, I always print several copies of the same subject, because each time I cut a piece of paper I ruin adjacent pieces. In the photo you can see the effect of the two shells used for the petals: the lighter stuff is white mop, the darker is australian greenlip abalone. Here is the writing made with golden mop. And this is the final effect when everything has been inlayed. I've also completed the flamed maple binding on the headstock. I have to improve my skills to cut miters 6 Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted October 20, 2017 Report Share Posted October 20, 2017 I'm not sure I've ever seen inlay of this quality on a guitar before... Last time I saw anything close, it was on a priceless cupboard made in the 18th Century and now pride of place in an English Country Manor House that tourists flock to see.... How will you prevent chipping when you drill out the 5th string tuner hole? Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 20, 2017 Author Report Share Posted October 20, 2017 19 minutes ago, Andyjr1515 said: I'm not sure I've ever seen inlay of this quality on a guitar before... Last time I saw anything close, it was on a priceless cupboard made in the 18th Century and now pride of place in an English Country Manor House that tourists flock to see.... How will you prevent chipping when you drill out the 5th string tuner hole? Thank you Andy, I'm really flattered for this comment To cut the hole I used a drill press drilling the headstock from the back and going really slowly. It was stressful! Quote Link to comment Share on other sites More sharing options...
Mr Natural Posted October 21, 2017 Report Share Posted October 21, 2017 really impressive work @MassimoPL77. You obviously love inlay- I can't even imagine cutting that much pearl. Well done and it looks incredible. Quote Link to comment Share on other sites More sharing options...
Prostheta Posted October 21, 2017 Report Share Posted October 21, 2017 Absolutely excellent, @MassimoPL77! I couldn't agree more with the comment already made. This is a stunning display of precise controlled work, which is exactly what a Les Paul benefits from. Hold up, let me ask my wife what she thinks.... Quote Link to comment Share on other sites More sharing options...
Prostheta Posted October 21, 2017 Report Share Posted October 21, 2017 As I took Nina through each of the pictures, she said "huh!" in surprise more and more....hahaha....Nina is also a woodworker, but unlike me, not by trade. Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 22, 2017 Author Report Share Posted October 22, 2017 On 21 ottobre 2017 at 3:16 AM, Mr Natural said: really impressive work @MassimoPL77. You obviously love inlay- I can't even imagine cutting that much pearl. Well done and it looks incredible. Thank you! On 21 ottobre 2017 at 10:48 AM, Prostheta said: As I took Nina through each of the pictures, she said "huh!" in surprise more and more....hahaha....Nina is also a woodworker, but unlike me, not by trade. Thank you Prostheta! I'm glad that Nina liked it! Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 22, 2017 Author Report Share Posted October 22, 2017 Now the guitar is almost finished so I took a photo with the hardware. I choose golden hardware, because I think that it matches better with the wood and complements the golden mop purfling. I f I could go back, maybe I would also put EVO gold frets... Now it's time to varnish. I didn't want to dye the wood, so to get an hi gloss finish i decided to use polyurethane and acrylic 2k finish. This combination is really easy to sand and you can get a mirror surface with no need of wet sanding. This is the guitar after clear coat. The mop stands out a lot under lacquer! And this is there result after finishing and buffing. I couldn't be more happy! 3 Quote Link to comment Share on other sites More sharing options...
Prostheta Posted October 23, 2017 Report Share Posted October 23, 2017 Even the neck tenon in the pickup rout looks beautiful! 1 Quote Link to comment Share on other sites More sharing options...
MassimoPL77 Posted October 23, 2017 Author Report Share Posted October 23, 2017 (edited) Here are some pics of the assembled guitar: In addition to standard three wires, I had to use other two for the split coils, so, all in all, there are five shielded wires running through the body. I was a little worrying about noise, but luckily the guitar is not noisy at all! The sound of the guitar surprised me: having used really dense woods like ebony and ash for the body, I was waiting for a more trebly, sharp sound, while I think that the guitar sounds equilibrated. I wonder if this depends on the large chamber routed in the body. Edited October 25, 2017 by MassimoPL77 1 Quote Link to comment Share on other sites More sharing options...
meatloaf Posted October 26, 2017 Report Share Posted October 26, 2017 Wow what a stunning guitar, you must have the patience of an angel, that inlay work is absolutely awesome and the best I have seen, Beautiful work. absolutely love it. 1 Quote Link to comment Share on other sites More sharing options...
Woden Posted October 26, 2017 Report Share Posted October 26, 2017 The talent on here blows my mind sometimes. Obviously your inlay work is incredible, but the overall package is extremely classy in every regard. As you said, the only improvement you might have made is using the EVO gold fretwire, but you can always upgrade them one day if you wanted to. I'm definitely not entering GOTM this month now, haha! Honestly, this may be the nicest Les Paul I've ever seen. Would hate to try and value it but surely we're talking many thousands. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.