Jump to content
Entry in the April 2024 Guitar of the Month contest is now open ×

avdekan

Established Member
 View Profile  See their activity

  • Posts

    76

  • Joined

  • Last visited

 Content Type 

Everything posted by avdekan

  1. avdekan
    I would just use more clamps. Using too few clamps makes you use a lot of pressure in order to get a good squeeze-out of glue, whilst potentially starving the area under the clamps and is not good for the clamp itself in the long run. I prefer using as many clamps as comfortably possible with moderate pressure. In the end its the power of numbers that does it.
  2. avdekan
    No problem. Traditional classical guitar bridges with scales from 640mm to 665mm all have the "same" straight saddle. Not being able to individually intonate strings is a problem in itself though...
  3. avdekan
    What type of glue did you use when you built it? If it was hide glue you can detach the top using heat, a mixture of hot water and spirit, and some patience. With carpenter's yellow/white glue (i.e. titebond) I wouldn't bother saving the top and just plane it off. If you have a set neck you might want to remove that too before planing. good luck.
  4. avdekan
    I don't like it too close to the bridge (too much "twang"). I say locate the bridgewise pole at 25.80697580112788mm (the square root of 666mm) from the bridge
  5. avdekan
    I think that unless the body design is radically different then the "traditional" centered mass approach, you can expect similar results from different body shapes using the same material and mass. Doing a 'x' shape body that's one meter long using 1x2" beams will have enough mass, but the flexibility of the design will probably cause a loss of sustain.
  6. avdekan
    Ipe? That fits the clues ...but no. I suppose this game sucks? SR last try: a weird subspecies of Bubinga?
  7. avdekan
    Pin router for the rough thicknessing (without the pin!). high angle (55 degrees or above) hand plane for the fine work. about the home made drum sander- benedetto's archtop book has a nice description of one in which the drum is fixed and the bed is adjustable using a hinge on one side and a lifting screw on the other. in order to change the thickness you tip the bed's angle. Fairly simple after you can figure out how to construct a perfectly square and stable mounting for the sanding drum...
  8. avdekan
    Ipe?
  9. avdekan
    If you build the guitar for yourself, and you don't use tune controls, I think not putting one is the right thing to do. However, I would make the electronics cavity big enough to accommodate a theoretic tone potentiometer (at it's would-be place), so that if one day you will discover that you do want a tone control - you could easily add one just by drilling and rewiring.
  10. avdekan
    Cool! Melvyn's book on electric guitars is what started my journey into this addiction. I hope the informative and user friendly nature of his first book is present in this one as well. Will find out soon enough.
  11. avdekan
    The (happy) client who just picked up this guitar couldn't think of a proper name for it (her!!), so I will temporarily name it "the 5 Pounder" - after its weight. Sapele / figured Maple body. Sapele neck. Ebony fretboard, electronics cavity cover, recessed scratch-plate and knobs. Strandberg headless system: bridge and string locks. Gold MOP face and side dots. Bone nut. Schaller strap locks. BKP custom made alnico III humbuckers. Volume / Tone / 3 way pickup selector / Series-split-parallel mini switch for each pickup. Double action truss rod. More pics of the Finished guitar can be viewed here: http://www.facebook.com/B.M.handmade.guita...135576636474094 And the Building process photos are here: http://www.facebook.com/B.M.handmade.guita...135576636474094 Cheers.
  12. avdekan
    Ashtray Dip holder... put in more than one like me and its a chip AND dip holder ! I'll take a picture of the guitar served with guacamole (the 2k finish is Glasurit so it should handle it) You could also make millions by taking this idea a step further, selling microwave dinners in totally playable guitars. I don't do it only because I'm too lazy.
  13. avdekan
    I assembled the guitar and the grounding wire thread I drew beneath the string locks works perfectly fine. I still need to do the final setup, But even as it is, after playing and hearing it a bit, I am very pleased with the result. Words of praise are due to Ola Strandberg for his cleverly designed bridge and the quality of it's fabrication, and to Tim Mills from Bare Knuckle Pickups for yet another amazing pickup (custom made alnico III set). The entire build process can be viewed here: http://www.facebook.com/B.M.handmade.guita...135576636474094
  14. avdekan
    have you considered using banjo tuners or the Steinberger ones?
  15. avdekan
    Haven't done it yet, but I was thinking of running a wire between the screws that attach the string clamps, which the strings rest against. clarification: one thread of a braided wire under the string clamps.
  16. avdekan
    Haven't done it yet, but I was thinking of running a wire between the screws that attach the string clamps, which the strings rest against.
  17. avdekan
    It's doable, but involves a lot of hassle every time you tune (see reply above). another point to consider is that every time you replace a string it requires you to screw the pin out, or else you will find yourself with the pin bored to the bottom of the hole and ruining the thread in the wood surrounding it. turning the pin back and forth like that every string change will make it a little looser every time, until you will be forced to replace the pin with a thicker one, and at some point you will run out of sizes (that might take a long time, but still needs considering).
  18. avdekan
    Hi This is a commission done for an architect who got tiered of his 10 lb les paul and wanted something lighter. The basic design was his, with me giving advice on aesthetics and altering it to make it playable. In the end we came up with a very compact, yet comfortable design. At the moment I'm doing the final sanding before the sealing and finishing, which will be clear 2k. In the pictures you can see the guitar with the strings on. I put them just to make sure that everything is well aligned and working properly before I do the finish. Bridge is by Strandberg, Pickups are BKP custom made. The entire process so far can be viewed at my facebook page: http://www.facebook.com/B.M.handmade.guita...135576636474094 Cheers, Benjamin
  19. avdekan
    Cheers! The reason for the conversion it that I have a client who ordered a warmoth tele, and he had a set of texas special to put in it. only problem is that he had the neck made with a compound radius, which makes the bridge radi very flat, and the middle strings with noticeably higher output then the outer strings. will taking a rough diamond stone (manually) to the magnets while still on the pickup work? thanks
  20. avdekan
    Could you elaborate? From What I know of telecaster bridge pickups, the plate is flat and the pole pieces vary in length. shortening the tall ones will remove some of the magnetic substance, but it will only make them similar to the outer magnets. am I missing something here?
  21. avdekan
    Hi Can I safely remove the two center magnets in a tele bridge pickup, cut/grind them a bit, and replace them back into the pickup without causing damage to the pickup? Thanks.
  22. avdekan
    Hi I started working on a guitar that will be finished with clear poly. the problem is that all the places near where I live that sell Glasurit ans Dupont (brands I know I can count on) are very happy to sell by the galon . However, I found this store nearby that Imports De-Beer ans sells it relatively cheap, and more importantly, in 1 liter cans! Has anyone had any experience with any of their finishes. any input will be helpful. thanks.
  23. avdekan
    [quote name='jaycee' post='428161' date='Jun 24 2009, 11:12 PM']Lemmy[/quote] +100,000
  24. avdekan
    scale length is 25.5" and the guitar is not a lefty - the headstock is just reversed.
  25. avdekan
    I'm coming back on a project that was on hold for a while now. this is going to be a 29 fret 6 stringer neck through, with 2 Q-tuner humbuckers (super high & high z) right next to each other, in the bridge and "middle" position. Since it's a metal axe, I'll put a 4 way (tele) lever pickup selector with a - both unbelievably hot pickups in series - position, which will probably suck but simply has to be done. eventually there will also be a 15mm, 45 degrees beveled edge around the body so it will not look so bulky. and it will probably be black (unless I go bananas and give it to a paintbrush (edited: airbrush!!!) guy who will make it look like a rusty old axe . as I'm in the middle of an exam period, progress will be slow during the upcoming month or two. I hope to finish this one before the start of the next academic year. B
×
×
  • Create New...