Jump to content

borge

Established Member
  • Posts

    481
  • Joined

  • Last visited

About borge

  • Birthday 02/05/1906

Profile Information

  • Location
    gisborne, new zealand

borge's Achievements

Proficient

Proficient (10/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. It looks like your two diagrams are electrically identical,the only difference is the physical location of the batteries earth,it's earthed at the jack in the 2nd pic and the earth pad on the PCB in the first. To disconnect the passive signal from the circuits input when the circuit isn't in use (ie when the bass is plugged into an amp) you need to break the connection between the left lug of the passive vol. pot. and the circuits input (it's a red wire) when a lead is plugged in. Jack 'IX' in this link is what you need. http://www.switchcraft.com/Documents/Jack_Schematics.pdf wired: top lug-left lug of vol. pot. 2nd lug- PCB input 3rd-passive output from centre lug of vol'pot' 4th-earth this'll stop any loading of the passive output when plugged into an amp, but you still have the problem of the circuit being on at all times and draining the battery. If you could get a hold of the circuit's schematic or the input impedance from the manufacturer you could get an idea of whether the loading will be an issue.
  2. having the signal going to the active circuit at all times will almost definately load down the output, whether it'll be a problem depends on your taste and the circuit. I'd suggest using a switching output jack that'll dissconect the signal from the active circuit when a lead is plugged in. Assuming, of course, you won't want to use both the internal speaker and and external amp at the same time...
  3. I've never heard of putting a Wah in the effects loop...
  4. All signals should be in sheilded cable, then the need for additional sheilding (copper tape ect) is reduced/eliminated. Any unearthed sheilding will increase noise. get rid of the single ground wire, connect the sheilded cable to the jack sleeve and the back of a pot. Earth loops/star grounding aren't always a big concern, all fenders have earth loops-the pots are earthed via the foil sheild AND by wires soldered to thier backs..relying on just the sheild would've been cheaper and (probably inperceivably) quieter, yet leo scrounge fender sprung for both for reliabilities sake or something like that
  5. sounds like you want a dual ganged pot, not a dual concentric pot? I'm a bit confused by your explaination. So if i'm understanding correctly here goes the simplist route i can think of... outputs of pickups go to dual pots, then onboard pickup selector of your choice then jack tip - mono operation complete. stereo operation - put onboard selector switch to 'neck' pos. (neck sent to jack tip) flick 'stereo-mono' switch (a spst only is required) which connects bridge signal to jack ring. unless you want to go active and design a circuit which will recognise weather a TS or TRS jack is inserted and switch to mono or stereo accordingly...
  6. asides the hum, is it fuctioning correctly? What affect does touching the strings have on the hum? what about touching the jack plate?
  7. Not sure why you'd need a schematic either, seeing as you're going with EMG's. EMG has schematics on their site.
  8. Just saw this in the OP, splitting one HB only requires a latching SPST. Not necessarily, the momentary switch could energise a SPST relay to do the coil splitting switching, no need for the guitar signal to have any active circuitry but no need really: The microswitches in arcade switches are the same as you'd find in washing machines, dishwashers and a myriad of other applications, your local appliance repair shop will have a big box of them laying around, take your momentary one in and they may swap it for a latching one or sell you one for a few dollars
  9. All the arcade machines I've worked on have had microswitches that pop into the actuator like this: http://www.athomedownunder.com/parts/arcade_buttons.shtml all you need to do is find the right button for you and replace the microswitch for a latching DPDT
  10. yes, and it's a fact modern test equipment is more acute than ANY human ear ie EJ's claim could be easily discredited by a simple test, not that that's required, anyone with electrical knowledge could tell you a slight variation in series resistance will cause a slight voltage change, but nothing compared to the normal variation due to power grid loading - ie the mains voltage variation throughout the day due to changing demand on the grid is many times larger than the voltage variation due to a possible slight difference in series resistance between two different fuses. I digress..
  11. its true - but its that same subjectivity we use when choosing a guitar and listening to music. I dont need scientific tests to tell me a piece of music sounds good and i dont need scientific tests to tell me if a guitar sounds good - its all about what pleases my imperfect human ears. Because music is art and therefore subjective, the frequency spectrum of different woods is not one is measurable the other is not. You saying a guitar 'sounds good' means about as much as me saying the same guitar doesn't 'sound good', they're just opinions, nothing more, nothing less, It has no bearing on comparing the sound of "sapele vs mahogany" or any other woods. And so will mine, but you and I expect differences whereas bartbrn doesn't, we both hear what we expect/want to hear.. yet other claim to hear the difference between capacitors and pay a premium for PIO, or bumblebee caps... who's right? you or them? You can see an interesting comparison of caps here: http://freestompboxes.org/viewtopic.php?f=6&t=12118&hilit=scientific (sorry, think you may need to join the forum to access it, but it's well worth it, and a great forum to boot) I would like to see the same frequency comparison software used for bartbrn's experiment, then we would have some actual facts to go off
  12. playing guitars at a music shop will not give any useful data, humans are too subjective and prone to placebo. No, the fundamental note (440) will vibrate identically, the amplitude of each harmonic will determine it's 'tone'. All easily measurable with test equipment to give useful, comparable data. Prostheta-ANYTHING can be quantified in the lab, you just need a large enough sample size I believe the woods used do make a difference but until I see some actual evidence I wont be spouting my easily biased, placebo ridden findings to anyone. from where I stand the sun appears to rotate around earth, I keep that to myself also... If we all took what we, or others 'hear' as useful data then buying things like THIS should seem totally normal what effect tacking on 2m of high quality cable to the masses of the lowest possible cost (while meeting safety specs) cable leading to that point would have is beyond me...but if someone hears it, power to them.
  13. That will also affect the taper. You can get 300k pots quite easily. most pots (and other electrical components) have a tolerance of +/-20% so your average 300k can be anywhere between 240k and 360k, a 250k pot will be between 200k and 300k and so on... it's very possible a '300k' pot will have a lower value than a '250k' pot, ie don't worry about it to much
  14. there really is no 'better', the lower the pot value is the more output and treble is bleed to ground. so if you want slight less output and treble use lower value pots.
×
×
  • Create New...