Entry for December 2019's Guitar Of The Month is open - ENTER HERE!
Search the Community
Showing results for tags 'guitar build'.
Found 4 results
I picked this body up on ebay. Someone laminated 1/4" oak, mahogany and maple to 1 1/2" poplar to achieve a standard 1 3/4" strat body thickness. I didn't mind, in fact I kind of liked it. I always hated a blank white canvas so to speak, so here was something to work with and hopefully improve. I was going to go with the strat shape but got turned on by some research of the Paul Bigsby guitars of the late 1940's. Could I honor his aesthetics in my own build? Hope so.
I am building my first 8string and first laminated neck. I am happy using hand tools, and take great pride in planing wood square and smooth by hand. However, I just finished gluing up the neck of my current build and am beginning to worry about the rip sawing that is going to be required for the rough cutting of the neck profile. It will have to be by hand.....I don't have a band saw. Any comments and advise on how to proceed would be gratefully received. The blog on the build can be reviewed here. Thanks for any advise. https://clareguitar.com/2018/03/19/starting-to-make-some-progress/
Hey Everyone! Welcome to my new thread on my first proper guitar build! I've been designing this for a while and I'm currently doing an accurate drawing of what it will look like. I had help from people like @ScottR, @curtisa and more to progress in my design and make it better. So thank you to all of them. Here is the link to that thread. Just so you know, I have experience with woodworking and others so I'm not going into this with nothing. The Design So I have been designing off of a telecaster, shape wise, as I have always loved the shape. Other guitars I have designed from include a PRS, Gibson and one of my current guitars, a Lag Arkane. It is a 25" scale with 24 Frets. To start this whole project off, I drew round my Lag Arkane body to get a rough outline. Then I shaped the guitar from that, adding the Telecaster shape. The headstock I designed off a PRS and a guitar that an old guitar buddy was given, a Seraph Sabre. Look him up, Jon Beedle. Here's the original rough design shape of both guitar and headstock. After I got the rough design, I attempted at creating an accurate design however it failed because of improper measurements. So I scrapped it, you can see it in the other thread. The Hardware and other stuff Wood I've been looking into different kinds of wood for this guitar, however I finalised on Black Korina for the body. I made this decision because 1 I like the wood and 2 I can get my hands on it quite easily! I'll need two halves of it so I can route out the middle of the guitar and then glue the top over it (If that makes sense). For the neck I was thinking just Mahogany as I have a lot of very old mahogany to use. It's about 200 years old! and then an ebony fretboard. Electronics I'm thinking humbuckers, don't know what yet (leave suggestion if you wish) but one in the bridge, one in the neck. I was looking into P90s but i'd rather use pickups I'm familiar with at first. I will have the input on the front, like an SG with two Tone and a Volume Knob. I'm hoping to use a Gibson switch as my selector for pickups. Other Stuff The bridge is cheap (£16) but I don't wast anything expensive at the moment. I got it from Northwest Guitars. It's a hardtail and it's chunky which is what I wanted. Currently up to this day I only have this. The Build Last night, 18/02/17, I embarked on a new adventure. I had the advice of people on the other thread, had the equipment, had the pride so I set off drawing a new design. I started by placing my ruler down on the table and drawing out a beautifully straight 25" line for my High E to nut scale. I then made a mark where the 24th fret will be and drew a line 90 degrees to it (you'll see in the pictures) and then added 3mm and that is where my pickup shall go. At the Bridge end of the scale length, I got my bridge that I bought and measured it up to the line with my High E. (My High E saddle is protruded 85%-ish-of the way out). I then went about sketching around the bridge. Then I took the Saddles off the bridge and drew the 5 holes where the bridge is screwed on and then the 6 holes for the strings-see images. From there, I got the measurement from E to E which was 54mm and added 4mm to each side. From there I drew a line from the middle marks on the bridge to the Nut in order to get the fretboard width. As shown in the first few drawings. Upon starting this at 11;25 on 19/02/17 this is all I have done. I plan on finishing this drawing soon and then buying the wood and starting!! Next I am going to mark the humbuckers and draw the body shape and headstock.
You spend all that time and a shit load of money building a guitar,( Warmoth Body & Neck) And sometimes you wonder is it all worth it.. lol. I FINALLY plugged it in for the first time tonight.. Just AMAZING !!!! And yes i have a few more things like the custom head stock decal. which going to be named " Sleeper " Road warn strat. maded to look old ( You old guys know what im talking about Looks stock until you look very close and under the hood.. lol ) And string guides. But it turns out to be a strat on steroids. Just AMAZING !!!