Quarter Posted March 9, 2010 Report Share Posted March 9, 2010 Bryans a good guy and is always very helpful. His PUF would be a excellent choice too. Its a little more vintage voiced than the BG Bucker, though the BG Bucker is based on a vintage tone also, maybe a bit more of a modern sound to it if that make sence. One thing I do like about the BG Bucker is it has a very good split tone and in general has a lot of chime to it. A neat in between pickup is I've had Bryan use an A4 mag like on the PUF instead of the A5 the BG Bucker normally uses. Its a particularly nice combo on a brighter body like maple or walnut. Here is a poorly played clip of some clean noodling with a BG-Bucker in HB mode. Its not Hawaiian, but might give you a bit of an idea. http://www.4shared.com/file/237346348/8fb5...-bg-c-msc1.html Quote Link to comment Share on other sites More sharing options...
Ron. Posted March 10, 2010 Author Report Share Posted March 10, 2010 (edited) Bryans a good guy and is always very helpful. His PUF would be a excellent choice too. Its a little more vintage voiced than the BG Bucker, though the BG Bucker is based on a vintage tone also, maybe a bit more of a modern sound to it if that make sence. One thing I do like about the BG Bucker is it has a very good split tone and in general has a lot of chime to it. A neat in between pickup is I've had Bryan use an A4 mag like on the PUF instead of the A5 the BG Bucker normally uses. Its a particularly nice combo on a brighter body like maple or walnut. Here is a poorly played clip of some clean noodling with a BG-Bucker in HB mode. Its not Hawaiian, but might give you a bit of an idea. http://www.4shared.com/file/237346348/8fb5...-bg-c-msc1.html Hi Quarter, I understand what you're saying about the modern yet vintage tone of the BG-bucker, because the sound sample sounds just the way you described It. I like the sound. Could you please explain what you meant when you wrote "the BG Bucker is it has a very good split tone" Are you referring the sound with just one of the humbuckers (single coil) turned on? Thanks for the pickup comparison, It's very helpful. Ron. Edited March 10, 2010 by Ron. Quote Link to comment Share on other sites More sharing options...
Quarter Posted March 10, 2010 Report Share Posted March 10, 2010 (edited) Are you referring the sound with just one of the humbuckers (single coil) turned on? Yes, split / splitting in terms of a humbucker refers to running just one of the 2 coils that make up a common humbucker. While most any 4 conductor humbucker can be split, the results can vary from quite nice to weak and uninspiring. A commonly misused term for splitting is tapped. Tapping is very different than splitting and theoretically can be done to any style pickup by the builder / winder. It involves pausing the winding process and splicing in / tapping another wire mid coil to achieve a lower output setting when engaged. Edited March 10, 2010 by Quarter Quote Link to comment Share on other sites More sharing options...
Ron. Posted March 10, 2010 Author Report Share Posted March 10, 2010 Are you referring the sound with just one of the humbuckers (single coil) turned on? Yes, split / splitting in terms of a humbucker refers to running just one of the 2 coils that make up a common humbucker. While most any 4 conductor humbucker can be split, the results can vary from quite nice to weak and uninspiring. A commonly misused term for splitting is tapped. Tapping is very different than splitting and theoretically can be done to any style pickup by the builder / winder. It involves pausing the winding process and splicing in / tapping another wire mid coil to achieve a lower output setting when engaged. Hi Quarter, I would like to split the pickup as one option since I've decided to keep this build simple by only installing 1 humbucker near the bridge. So I'm guessing that I can turn on the humbucker as one sound option and split the humbucker as another option. Any good Books out there regarding electronics pickup wiring diagrams etc...? Thanks for the lesson. Ron. Quote Link to comment Share on other sites More sharing options...
Quarter Posted March 10, 2010 Report Share Posted March 10, 2010 Lots of info out there on the web. GuitarElectronics.com has a lot of good diagrams. Here is one using a push pull pot to do a screw side coil split http://www.guitarelectronics.com/product/W...ingle_Coil.html You could also do that with a dual pole dual throw toggle switch too, something like this http://www.guitarelectronics.com/product/S...dle-Chrome.html Quote Link to comment Share on other sites More sharing options...
Ron. Posted March 10, 2010 Author Report Share Posted March 10, 2010 Lots of info out there on the web. GuitarElectronics.com has a lot of good diagrams. Here is one using a push pull pot to do a screw side coil split http://www.guitarelectronics.com/product/W...ingle_Coil.html You could also do that with a dual pole dual throw toggle switch too, something like this http://www.guitarelectronics.com/product/S...dle-Chrome.html Thanks for posting the links Quarter. The diagram looks fairly simple. I was going to order some other electronic hardware from Stew Mac. It's time to slow down and get this right. Thanks, Ron. Quote Link to comment Share on other sites More sharing options...
Ron. Posted March 12, 2010 Author Report Share Posted March 12, 2010 (edited) Can someone tell me what can I use to cut nut slots in aluminum angle If I don't have nut files? thanks, Ron. Edited March 12, 2010 by Ron. Quote Link to comment Share on other sites More sharing options...
fngrpepr Posted March 13, 2010 Report Share Posted March 13, 2010 Hi all, good thread, I'm also working on my first lap steel. I've been wrestling with type of bridge and nut to use. I was already thinking about going with a bone nut, and then I saw this bridge in the stewmac catalog (http://www.stewmac.com/shop/Bridges,_tailpieces/Archtop_guitar_bridges/Archtop_Bridge_with_Bone_Saddle.html?tab=Details#details), it's an archtop bridge with a bone saddle. Anyone tried using one of these for lap steel? Is it overkill or too much trouble? I like that it's height adjustable, and since it's bone I figure I'd be able to level out the strings to undo the radius they have on it. The bridge is a little too wide for my design due to those wood feet, but I was thinking I would just saw off some of the end on both sides to make it fit. Quote Link to comment Share on other sites More sharing options...
Ron. Posted March 13, 2010 Author Report Share Posted March 13, 2010 (edited) I made a aluminum nut today and cut the slots using a xacto saw for the initial cut, and then I used a small triangle file. I strung the Low E string, and It stayed in the slot and in tune. I don't know about the rest of the slots yet. I'm not too concerned, because I can just make another one from the 1/8" x 1/2" x48" aluminum angle that I brought for $4.95. Here is a picture of the peghead, It's not perfect but I think It'll work. Sorry for the crummy picture. As always thanks for all the help. Hi fngrpepr, Im sure someone with more experience will chime in later and offer a better opinion than I can regarding the bridge you posted. As you probably read from my previous post, I'm using a Gotoh hardtail non tremolo bridge, and I have It max out height wise. It's about a half inch high as Quarter said It would be, which seems to be adequate. I'm planning on using a fingerboard that will be about 1/8" thick so I don't bottom out with the bar. Regards, Ron. Edited March 13, 2010 by Ron. Quote Link to comment Share on other sites More sharing options...
Quarter Posted March 13, 2010 Report Share Posted March 13, 2010 That looks great Ron, I like your recurve on top. There have been a bunch of threads here over the years on alternative nut slotting tools. Feeler gauges with teeth notched in them and welding torch tip cleaners seem to come up quite often. Needle files can work fine if you find a set with the right sizes, in particular, a joint round edge style is helpful. A joint edge file is basically what nut files are and come in gauged sizes. Those Xacto razor saws are great for starting the slot. . fngrpepr ... an acoustic bridge certainly could work, but my reservations on that style is that I believe its radiused on the bottom and designed as a floating bridge. Other issues you may have is the overall height and grounding of the strings. Quote Link to comment Share on other sites More sharing options...
Ron. Posted March 13, 2010 Author Report Share Posted March 13, 2010 That looks great Ron, I like your recurve on top. There have been a bunch of threads here over the years on alternative nut slotting tools. Feeler gauges with teeth notched in them and welding torch tip cleaners seem to come up quite often. Needle files can work fine if you find a set with the right sizes, in particular, a joint round edge style is helpful. A joint edge file is basically what nut files are and come in gauged sizes. Those Xacto razor saws are great for starting the slot. . fngrpepr ... an acoustic bridge certainly could work, but my reservations on that style is that I believe its radiused on the bottom and designed as a floating bridge. Other issues you may have is the overall height and grounding of the strings. Thanks Quarter, for all the measurements and tips that you offered so generously. I know It would not have turned out as well otherwise. I still have to refine It a little more. I called a local welding supply store and they have the tip cleaners for $7. I wouldn't mind buying the feeler guages too because they also seem to be reasonably priced. I googled Feeler Guages which ones do you recommend? Also should I buy steel or brass, or It doesn't matter? http://www.ppe.com/10cat/0237.pdf Thanks, Ron. Quote Link to comment Share on other sites More sharing options...
Quarter Posted March 13, 2010 Report Share Posted March 13, 2010 No problem Ron, glad to help if I can. ... For the feeler gauges, I'd suggest the steel as they will be harder and more suited to using them for cutting. Most any auto parts store will have some and I've seen the torch tip cleaners in Lowes, Home Depot too. All of these are fine for a project or two, but in the end, its hard to beat a set of real nut files if you do much nut work. Quote Link to comment Share on other sites More sharing options...
Ron. Posted March 14, 2010 Author Report Share Posted March 14, 2010 No problem Ron, glad to help if I can. ... For the feeler gauges, I'd suggest the steel as they will be harder and more suited to using them for cutting. Most any auto parts store will have some and I've seen the torch tip cleaners in Lowes, Home Depot too. All of these are fine for a project or two, but in the end, its hard to beat a set of real nut files if you do much nut work. I agree that using these cheaper tools for not slotting should be temporary, I will eventually get the fret slotting files. I'll check the local auto parts store monday for the feeler guages. Thanks, Ron. Quote Link to comment Share on other sites More sharing options...
DC Ross Posted March 14, 2010 Report Share Posted March 14, 2010 (edited) Torch top cleaners do not work. When I was starting out, I didn't want to shell out the cash, so I gave these a shot. It's not like they kind of work and will get you by. They just outright do not work. Edited March 14, 2010 by DC Ross Quote Link to comment Share on other sites More sharing options...
Ron. Posted March 14, 2010 Author Report Share Posted March 14, 2010 (edited) Torch top cleaners do not work. When I was starting out, I didn't want to shell out the cash, so I gave these a shot. It's not like they kind of work and will get you by. They just outright do not work. Hi DC Ross, I was planing on trying both the Feeler Guages and the tip cleaners, but then I decided to get just the feeler guages, thanks. Ron. Edited March 14, 2010 by Ron. Quote Link to comment Share on other sites More sharing options...
Ron. Posted July 20, 2010 Author Report Share Posted July 20, 2010 I just wanted to post some (not so great) pictures of my electric lap steel guitar that I built. I made a lot of mistakes but learned from all of them. The guitar is made of kiln dried poplar from a local lumber yard. I had It painted Metalic Pelham Blue by a pro at a very reasonable price. The pick up is a GFS Pro-Tube Lipstick pickup that I split so that the north coil sounds like a single coil and the humbucker can be played in series (I hope I'm using the correct terminology). The Bridge is a Gotoh Hardtail string through Bridge from Stew Mac, Tele Electrosocket jack, Grover Sta-Tite tuners which work great. I do plan on making another pickguard in a week or so because I drilled a couple of pickguard screw holes in the wrong place, and I burned the side of the pickguard a little with the soldering Iron. I designed the fingerboard in Adobe Illustrator, and had the design laser etched on "1/8" black top white core board" turned out nice. I would like to thank everyone who contributed to this thread and the Project Guitar forum. I would especially like to thank Quarter for patiently answering all of my questions. I don't think It would have turned out as well as It did with out your help. Thanks Quarter, you are a great teacher, and you are very generous. Ron. Quote Link to comment Share on other sites More sharing options...
Quarter Posted July 20, 2010 Report Share Posted July 20, 2010 Great job Ron, I like it a lot! Quote Link to comment Share on other sites More sharing options...
ScottR Posted July 20, 2010 Report Share Posted July 20, 2010 It is great to see that you put all the information you gleaned from that long and detailed list of questions to good use. The guitar looks great! I must say at the time I was impressed with the scope of the questions you asked. And I was also impressed with the completeness of the answers Quarter provided, not to mention the grace and patience with which they were delivered. I'm sure it is as gratifying to him to see what you were able to accomplish with the knowlege you gained as it was you to build this fine instrument. Well done to you both! So how does it sound? SR Quote Link to comment Share on other sites More sharing options...
Ron. Posted July 20, 2010 Author Report Share Posted July 20, 2010 Quarter Wrote: Great job Ron, I like it a lot! Thanks Quarter, I was just trying to make good use of all the great information that you provided. It is great to see that you put all the information you gleaned from that long and detailed list of questions to good use. The guitar looks great! I must say at the time I was impressed with the scope of the questions you asked. And I was also impressed with the completeness of the answers Quarter provided, not to mention the grace and patience with which they were delivered. I'm sure it is as gratifying to him to see what you were able to accomplish with the knowlege you gained as it was you to build this fine instrument. Well done to you both! So how does it sound? SR Hi,Scott It sounds nice to me. I brought a Vox Da5, and I found a few setting that I really like. The clean setting with a little a reverb added sounds really nice with the humbucker on. It also sounds nice in split mode (north coil on) I haven't had much time to play it but definitely like what I heard so far. I think that the GFS Lip stick humbucker offers a lot of tonal possibilities, particularly when split. I really life the GFS Pro-Tube Lip Stick pickup a lot. I also agree that Quarter was very patient and helpful answering the many question that I asked. I tried to ask questions that would give me a clear understanding of what I Should and shouldn't do. I hate copying other peoples designs, so I tried to ad my own little twist to what I was building, and Quarter provided me with information that allowed me to do that. I think that this is one of The best Lap Steel building threads ever, thanks to Quarter and the other contributors. Ron Quote Link to comment Share on other sites More sharing options...
Ron. Posted July 21, 2010 Author Report Share Posted July 21, 2010 (edited) Hey everyone I want to thank WezV, Akula, Saxon Marsh and Tim3 for contributing to this thread as well and for all their help, and anyone else that I may have missed, thanks guys. Special thanks to the The Project Guitar Forum. Ron Edited July 21, 2010 by Ron. Quote Link to comment Share on other sites More sharing options...
WezV Posted July 21, 2010 Report Share Posted July 21, 2010 that may be the coolest lapsteel around Quote Link to comment Share on other sites More sharing options...
Ron. Posted July 21, 2010 Author Report Share Posted July 21, 2010 (edited) that may be the coolest lapsteel around Hey WezV, I hope all is well. Thanks for the kind words. Thanks again for all of your help, much appreciated. ron Edited July 21, 2010 by Ron. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.