ProjectGuitar.com Posted April 23, 2013 Report Share Posted April 23, 2013 The Project Guitar.com "Guitar of the Month" contest is a showcase for all the members, so show us your axe in this thread! This contest is open to any and all members that enter and will be continued each month for a place showing your creation on the homepage! The winner(s) of course will have his/her guitar featured on the homepage of Project Guitar.com and if you have a website the picture will link directly to it if you so choose (even commercial site's). If your a forum member you will also be upgraded with a special badge to show you won! So show us your creation in this thread! You've got till sometime around the 23rd or 24th of May then this thread gets locked and the voting starts! Any Post that is not an entry will be deleted, feel free to start a new thread to discuss any guitar entered this month There may be more then one poll to determine winners in different catagorys at the end of this contest! Please post a maximum of your 4 best pictures per guitar entered Make sure Your Guitar has a Name or Nick Name as well otherwise one will be given to it Side note, if you are unable to post a picture you can e-mail one to Brian and it will be posted for you, or ask forum members how to post pictures, they are very helpful. Link to comment Share on other sites More sharing options...
Boggs Posted April 24, 2013 Report Share Posted April 24, 2013 Another RockBeach CB-III in Walnut and Tulip Poplar with an olivewood neck and pistachio fingerboard. This is sporting Tesla pickups (Opus 1 neck and middle and VR Extreme bridge) with the bridge pickup switchable between series and parallel with a "slap pot switch". It is not a push-pull. Very convenient to use. Link to comment Share on other sites More sharing options...
curtisa Posted April 25, 2013 Report Share Posted April 25, 2013 Afterimage Guitars - TSC6 "Blackflow" Body - Tasmanian blackwood with tiger myrtle carved top Neck - Tas blackwood/Tas myrtle with figured gidgee fretboard Inlays - Celery top pine rings with gidgee centres Scale length - 25.5" Radius - 16" Trussrod - Allparts Tuners - Hipshot Griplock Nut - Graphtech black Tusq Frets - Jumbo stainless steel Pickups - Seymour Duncan JB bridge, STK-S4 stacked humbucker neck Bridge - Wilkinson VS100 trem Electronics - 1x vol, 1 x 3-way toggle More photos and build thread: http://projectguitar.ibforums.com/topic/47114-build-5-singlecuttele-style-tsc6/ Link to comment Share on other sites More sharing options...
Menapia Posted April 26, 2013 Report Share Posted April 26, 2013 Cairbre Body ... Sycamore on Sapele . Neck.... Rose wood and maple with a birdeye maple fingerboard and flame maple binding . Pups.... Di Marzio Paf pro ,positions 2 and 4 are wired in parallel ( inside and outside coils ). Bridge.. Ibanez Edge. Tuners.. Wilkinson Inlays... MOP and Abalone. Ep Mega switch cts 500k pot. Lacquer finish . 1 Link to comment Share on other sites More sharing options...
andyt Posted April 28, 2013 Report Share Posted April 28, 2013 Dirty Frank Built with whatever wood and parts were lying around in the shed Sapelle body flame maple neck and board mismatched scrap parts Schaller floyd Dimarzio MoJoe build thread http://projectguitar.ibforums.com/topic/47174-striped-frankie-probably/ Link to comment Share on other sites More sharing options...
Hitone Posted April 29, 2013 Report Share Posted April 29, 2013 Gone Fishing Resin Cast body - embedded heavily weathered barn wood, vintage lures, hook tin, Bomber Lures box, and a Split Shot tin Fretboard is Flamed Maple with a Rosewood strip, compound radius 10"-14" Pickguard - Red Oak Back - Cedar with walnut strip Backplate - Leaktite #5 Neck - Mahogany, Walnut, Mahogany Electronics - Alnico 5 single coils Oil Finish Built to be donated to the Richardson Wildflower Festival More picks on my facebook page. NEW I just added a demo video. Link to comment Share on other sites More sharing options...
argytar Posted May 12, 2013 Report Share Posted May 12, 2013 (edited) Hi! Long time no see , I doubt that anyone remembers me, I 'm the doc from Greece (PRS project and Esperanza). I 've started building again so for this month I have the following attempt: It s a lefty guitar I made for my best man. It's got a 2-piece mahogany body , QS mahogany neck set to an angle of 3.5 degrees, indian rosewood fingerboard and the headstock reads KLEO (ie Cleopatra the name of my wife's maid of honour and also his wife). The guitar sports Tone -Pros tuners and tune-o-matic bridge and the strings go through the body , ending in chrome vintage ferrules. It s light at about 7 pounds and has a set of tonerider alnico IIs installed. There is also a splitter switch and of course volume - tone 3-way switch. It was pore filled with wood putty and finished with teak oil. Hope ya like it! and one from the back when it was being constructed , now it has a black plastic cover http://i212.photobucket.com/albums/cc223/argytar/DSC00263-1.jpg Edited May 12, 2013 by argytar Link to comment Share on other sites More sharing options...
argytar Posted May 12, 2013 Report Share Posted May 12, 2013 Hi! If it is posicle I would like to add the following video to the Kleopatra project entry Thanks!! Link to comment Share on other sites More sharing options...
Simo Posted May 14, 2013 Report Share Posted May 14, 2013 Spalted Maple Singlecut 24 frets, 25.5" scale Body: American Cherry Top: Spalted Maple Neck: Maple/American Cherry Fretboard: Ziricote Inlays: Sterling silver side dots Pickups: EMG P81/P85 Dunlop Flush-Mount strap locks Ebony knobs Body Finish: Rustins Plastic Coating (brushed) Neck Finish: Hard wax oil [ Link to comment Share on other sites More sharing options...
skelf Posted May 17, 2013 Report Share Posted May 17, 2013 First Reiver Guitar. All the woods used where supplied by Tasmanian Tonewoods. The guitar was built for Robert the owner and one of my main suppliers. Carved Blackwood top and back with Houn Pine core. She Oak finger board with 7 piece Celery Top Pine/Myrtle/Houn Pine/Blackwood. Schaller 3D bridge Hipshot Locking tuners, Dunlop Dual Design straplocks. P90 pickups into an East Tone Lifter circuit volume 4 way selector. Satin finish. Link to comment Share on other sites More sharing options...
ProjectGuitar.com Posted May 23, 2013 Author Report Share Posted May 23, 2013 Time to Vote go here> http://projectguitar.ibforums.com/topic/47329-guitar-of-the-month-for-june/ Link to comment Share on other sites More sharing options...
Recommended Posts