Jump to content

Guitar Of The Month For June

Recommended Posts

The Project Guitar.com "Guitar of the Month" contest is a showcase for all the members, so show us your axe in this thread!
This contest is open to any and all members that enter and will be continued each month for a place showing your creation on the homepage!
The winner(s) of course will have his/her guitar featured on the homepage of Project Guitar.com and if you have a website the picture will link directly to it if you so choose (even commercial site's).
If your a forum member you will also be upgraded with a special badge to show you won!
So show us your creation in this thread! You've got till sometime around the 23rd or 24th of May then this thread gets locked and the voting starts!
Any Post that is not an entry will be deleted, feel free to start a new thread to discuss any guitar entered this month
There may be more then one poll to determine winners in different catagorys at the end of this contest!
Please post a maximum of your 4 best pictures per guitar entered
Make sure Your Guitar has a Name or Nick Name as well otherwise one will be given to it :)
Side note, if you are unable to post a picture you can e-mail one to Brian and it will be posted for you, or ask forum members how to post pictures, they are very helpful.
Link to comment
Share on other sites

Another RockBeach CB-III in Walnut and Tulip Poplar with an olivewood neck and pistachio fingerboard. This is sporting Tesla pickups (Opus 1 neck and middle and VR Extreme bridge) with the bridge pickup switchable between series and parallel with a "slap pot switch". It is not a push-pull. Very convenient to use.


Link to comment
Share on other sites

Afterimage Guitars - TSC6 "Blackflow"

Body - Tasmanian blackwood with tiger myrtle carved top
Neck - Tas blackwood/Tas myrtle with figured gidgee fretboard

Inlays - Celery top pine rings with gidgee centres
Scale length - 25.5"
Radius - 16"
Trussrod - Allparts
Tuners - Hipshot Griplock
Nut - Graphtech black Tusq
Frets - Jumbo stainless steel
Pickups - Seymour Duncan JB bridge, STK-S4 stacked humbucker neck
Bridge - Wilkinson VS100 trem
Electronics - 1x vol, 1 x 3-way toggle





More photos and build thread:


Link to comment
Share on other sites


Body ... Sycamore on Sapele .

Neck.... Rose wood and maple with a birdeye maple fingerboard and flame maple binding .

Pups.... Di Marzio Paf pro ,positions 2 and 4 are wired in parallel ( inside and outside coils ).

Bridge.. Ibanez Edge.

Tuners.. Wilkinson

Inlays... MOP and Abalone.

Ep Mega switch cts 500k pot.

Lacquer finish .





  • Like 1
Link to comment
Share on other sites

Gone Fishing

Resin Cast body - embedded heavily weathered barn wood, vintage lures, hook tin, Bomber Lures box, and a Split Shot tin

Fretboard is Flamed Maple with a Rosewood strip, compound radius 10"-14"

Pickguard - Red Oak

Back - Cedar with walnut strip

Backplate - Leaktite #5

Neck - Mahogany, Walnut, Mahogany

Electronics - Alnico 5 single coils

Oil Finish

Built to be donated to the Richardson Wildflower Festival

More picks on my facebook page.

NEW I just added a demo video.




Link to comment
Share on other sites

  • 2 weeks later...


Long time no see , I doubt that anyone remembers me, I 'm the doc from Greece (PRS project and Esperanza). I 've started building again so for this month I have the following attempt:

It s a lefty guitar I made for my best man. It's got a 2-piece mahogany body , QS mahogany neck set to an angle of 3.5 degrees, indian rosewood fingerboard and the headstock reads KLEO (ie Cleopatra the name of my wife's maid of honour and also his wife). The guitar sports Tone -Pros tuners and tune-o-matic bridge and the strings go through the body , ending in chrome vintage ferrules. It s light at about 7 pounds and has a set of tonerider alnico IIs installed. There is also a splitter switch and of course volume - tone 3-way switch. It was pore filled with wood putty and finished with teak oil.

Hope ya like it!




and one from the back when it was being constructed , now it has a black plastic cover



Edited by argytar
Link to comment
Share on other sites

Spalted Maple Singlecut

24 frets, 25.5" scale

Body: American Cherry
Top: Spalted Maple
Neck: Maple/American Cherry
Fretboard: Ziricote

Inlays: Sterling silver side dots

Pickups: EMG P81/P85

Dunlop Flush-Mount strap locks

Ebony knobs

Body Finish: Rustins Plastic Coating (brushed)

Neck Finish: Hard wax oil





Link to comment
Share on other sites

First Reiver Guitar. All the woods used where supplied by Tasmanian Tonewoods. The guitar was built for Robert the owner and one of my main suppliers. Carved Blackwood top and back with Houn Pine core. She Oak finger board with 7 piece Celery Top Pine/Myrtle/Houn Pine/Blackwood. Schaller 3D bridge Hipshot Locking tuners, Dunlop Dual Design straplocks. P90 pickups into an East Tone Lifter circuit volume 4 way selector. Satin finish.




Link to comment
Share on other sites

This topic is now closed to further replies.

  • Create New...