Jump to content

thebhef

Members
  • Posts

    17
  • Joined

  • Last visited

Everything posted by thebhef

  1. Yeah, the new Steve Vai signatures have that. The falloff is great for setting low action. I hear it's a bitch to get proper intonation out of, though.
  2. Just make sure you don't get the disappearing pyramid fret wire.
  3. vwall's not selling them anymore, apparently. I emailed about a month and a half ago, and that's what he said. It might be worthwhile to ask again, though.
  4. I just put a couple of the film piezos in my Ibanez Edge III bridge. I had to take all the saddles off, loosen the screws that hold the top plates on the sustain block, and slid 'em in between. I wasn't watching the clock, so I'm not sure, but I'm sure it didn't take much more than an hour to do it. They're quiet as hell, though, so my next project will be a preamp for 'em.
  5. Carvin has left handed kits for the same price as the right handed kits. It's one of the options at the bottom of the order page. They run about 400 bucks
  6. You CAN get the sander, but you cannot get the little plastic contours to go with it without buying the whole kit, and those things wear out relatively quickly. I did a 22 fret neck in about 6 or 7 hours with an assortment of files and rasps that I got for about $10 at Menards.
  7. What's the story on those? Do they work about the same as a Floyd and just stay in tune better?
  8. I'm buying my parts for my guitar, and I've been looking at 7-string trems. I'd really like to get an ibanez, but the only place i know of to get it is going to run me about 300 bucks, sans locking nut, which adds another 90 to the price. I see Warmoth has licensed Floyd 7's with the nut included for less than half that, which makes me wonder if there are any serious quality issues with them, or if the Ibanez ones are just more expensive because they're harder to get. Has anyone tried Warmoth's out, or heard anything about them? The Warmoth bridge: http://www.warmoth.com/hardware/bridges/br...s_floyd_7string
  9. and maybe it will have a working pickup. Better tell him not to try making his own this time. Apparently, the pickup is an empty little pine box.
  10. I'm planning a 7-string with a 27 inch scale, and head end adjustment. I was looking at StewMac's hot rods for my truss rod. They come in 18 and 24 inch sizes. After doing some measurements, it looks like the 18 inch rod would leave about 2 inches of the body end of the neck without any rod. Is that a problem?
  11. I didn't officially take any stance, really. I do agree that the momentary button would be much easier. I know a short is much quieter than an open circuit, too, so I guess I don't agree with that. A/D 1|1 What about an effects processor and an expression pedal? That'd give the on-the-fly variability you're looking for, without bending over (unless you count the cost of the equipment).
  12. If you do go with the kill switch, you should get a N.O. momentary switch, and put it between your signal and ground wires. This is MUCH quieter than using the N.C. switch and breaking the circuit. It should go between your output jack and the rest of your electronics. I've done this on both of my guitars with no problems. If you really do need the hard trem effect, and don't mind doing some routing in your guitar, you could probably work something out with a 555 timer and a transistor to short the signal to ground.
  13. Negative. The only place I've seen white hardware is on Buckethead's guitar. I just realized that white on red would look awesome.
  14. Hey man, congratulations. I've got an RG350, and I have an Evolution bridge with a P.A.F. Pro neck pickup. The Evo is a dream for metal riffs. I don't use the neck pickup that often, and when I do it's usually for cleans, so I can't help you there. As far as a pickguard goes, you should be able to find one on ebay for less than 30 bucks. Probably 20ish.
  15. Are you saying the cavity isn't deep enough? Or is the bottom plate too wide? I would worry about messing up the pickup, so I'd rout the body more, since it will be covered by the pick guard.
  16. Hey all, I love the information on this site. I've been a member for a few months, this is my first post. I've got a red guitar with black everything else. I was wondering if anyone knows where I'd be able to find white tuners and a white locking trem/nut. The bridge I have is an Ibanez Edge III, so I'd prefer to put another one of those back in, but I really just want to know if anyone out there makes hardware in colors other than black, chrome, and gold. Any ideas? I want a bad ass candy cane guitar.
×
×
  • Create New...