Jump to content
Entry in the April 2024 Guitar of the Month contest is now open ×

Guitar1Jesse

Members
 View Profile  See their activity

  • Posts

    22

  • Joined

  • Last visited

 Content Type 

Everything posted by Guitar1Jesse

  1. Guitar1Jesse
    Can't you find plums at any grocery store?
  2. Guitar1Jesse
    I was wondering if there's anywhere to purchase a template for an RG neck pocket.
  3. Guitar1Jesse
    Lynch Mob rules! and that is some awesome paint work!
  4. Guitar1Jesse
    I think there should be a tutorial made on how to place the bridge... don't hammer me if it's a bad idea!! I just think it would help.
  5. Guitar1Jesse
    How do you do those cutouts with the bandsaw? i'm guessing they're too tight of turns to just cut along, so do you just cut out chunk by chunk or what?
  6. Guitar1Jesse
    Anyone?
  7. Guitar1Jesse
    Minwax Polyacrylic I believe is water-based. Can that be applied over oils (oils fully dried of course)?
  8. Guitar1Jesse
    if you want to spend the money on a brand new one, Ibanez will send you one if you send in the broken neck...
  9. Guitar1Jesse
    Ok, I know that half the scale length is from nut to 12th fret. My question is, is it measured to the center of the 12th fret? bridge-side 12th fret bar?, nut-side 12th fret bar? Also, am I safe to guess that measuring the other way would be from the front of the saddles? Hope you can understand my question...thanks a bunch!
  10. Guitar1Jesse
    Thanks
  11. Guitar1Jesse
    could anyone suggest any good clear lacquer for covering an oil-painted surface?
  12. Guitar1Jesse
    THANKS!
  13. Guitar1Jesse
    If I buy this will it fit most humbuckers? Will i be safe buying this with the intent to get your average seymour duncan/dimarzio humbucker? (sorry i don't know any models as of yet)
  14. Guitar1Jesse
    Thanks guys, I think I know what to do now
  15. Guitar1Jesse
    so do you just use a drill for the first 1/2" or so? So then the bearing will line up with the edge of the template?
  16. Guitar1Jesse
    I have not actually seen this set up or done, so I may be missing something very obvious, but my question is: When you set up your template and then rout it out, doesn't the router bit eat up the edge of the template? or do you just need to be that precise? or doesn't the cutting edge of the bit touch the inner edge of the template? also, how do you attach the template to the wood body?
  17. Guitar1Jesse
    Is there some way to just re-surface them? Without worrying about color, because i'm thinking about painting a design that would cover them up. thanks!
  18. Guitar1Jesse
    Is it possible to replace inlays that are all chipped and gouged up? If so, how do i go about doing that?
  19. Guitar1Jesse
    Drill and chisel...if you're serious please explain (sorry I don't know much about this stuff yet) any other methods besides renting a router?
  20. Guitar1Jesse
    Hi, check out this link and tell me if this will work for all my body cavity routing (pickups, neck, bridge, etc). dremel It's the first router guide on the page. I already have the dremel tool. Thanks!
  21. Guitar1Jesse
    i was thinking of purchasing a neck for real cheap, but it is real dirty and grimy. How easy is it to fix up? It doesn't seem too hard, or is it? Frets themselves are great, but the back of the neck and the fingerboard need work... just sand it down?
  22. Guitar1Jesse
    Hi - I'm sorry if this has already been discussed, but I just joined the forum 2 seconds ago... I was wondering if it is a good or bad idea to hand paint a design say with oils or acrylics and then apply a clear coat over the top for protection. What should I know before I attempt this?
×
×
  • Create New...