Jump to content

pike168

Members
  • Posts

    14
  • Joined

  • Last visited

About pike168

pike168's Achievements

Apprentice

Apprentice (3/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. Just found this place: http://www.cartersconsumables.co.uk/polish...94_104_201.html Theres so many diffrent polishes, Which would be my best best ? Thanks.
  2. I Bought this stuff http://cgi.ebay.co.uk/3m-Perfect-It-fast-c...11.c0.m14.l1318 Will it do ?
  3. Im trying to refinish a strat using the how to paint your guitar book from www.paintyourownguitar.com, Ive wet sanded the clear with 1500 grit paper and now i need to apply 3M Perfect-It Finishing Compound to complete the project, Only problem is that i dont know where to purchase it within the UK. Does anyone happen to know where i can get some, If not, could you recommend what product to use instead of the 3M stuff. Cheers
  4. I Have an LTD EC-1000 Guitar which are fitted with EMG 81 and 60 pickups, i would like to install the zakk wylde set but im unsure if i have the knowledge to do this. I Took out the pickups from the body (not de-soldered) and it seems they just have a simple 3-pin connector at the back of the pickup, is it possible to just unplug the stock installed 81's and 60's and plug the ZW Pickups in or will i have to solder everything again ?
  5. ok i have sanded it and painted yellow, do i have to sand the yellow and then paint on black or do i not have to sand the yellow and go straight onto painting the black?
  6. THANKS!! the links that both you guys gave me were FANTASTIC!! much appreciated.
  7. hi, i have sanded and primed my squire strat so its now very smooth and very white, i want to end up with this design for the body http://www.rocknrollvintage.com/prodimages/05%20evh%20b.jpg, to do this i will spray the whole body yellow and then put tape down to make the stripes, spray black and take of the tape so i have a black body and yellow stripes. Is this the correct way to make the design?? also two more questions, 1) what type of tape should i use, because wouldnt some just take paint of? 2) i have brought a spray can of "plasti-kote ployurethane varnish- satin" to spray at the end of the project is this stuff OK? sorry for all the questions but i need to be sure. thanks.
  8. i have checked the back of the tube and it says it is for plaster,wood,masonary and stone, as i am quite cautious i tried a little hole and it worked fine so i dont think that it will cause much hassle, but if you have any tips on filling please give cheers
  9. hey i FINALY got that green **** of, my brother gave me a product called "nitro something" and i workd perfectly, i accendentally got a few bits on my arm and the pain was terrible burned for ages but at least it is all of and now the body is clean. next i am going to sand it and when that is done fil small holes with a product called "pollyfilla" made by polycell, is this the correct stuff to use as i tried it on a small hole and it worked ok and i did not even sand it down, what do you guys think?
  10. that green stuff is not coming off, i have used heat, stripper and a sander any ideas to what it is and what to do?
  11. cheers, i am going to B&Q today and will buy 2 cans of the primer you recommended, 2 of the cracklin effect paint and 2 cans of the gloss polyurethane. thanks for help
  12. i have now totally stripped the paint of put underneath that there is a weird and tough coat of green stuff and i would like to known how to remove it, any idead would be helpful? also is this correct= when it is sanded give the body a couple of coats of this stuf= http://www.plastikote.com/plastikote/homef...oduct=decprimer then spray the colour http://www.plastikote.com/plastikote/homef...roduct=Cracklin finish it with this and sand and spray once more= http://www.plastikote.com/plastikote/homef...ct=Polyurethane cheers guys cheers
  13. cheers guys, i have used a heat gun and got rid off all the paint and there are no burn marks or darkening of the wood so i think that is was successful the only thing is, i have removed practically all of the black paint but underneath it is this green coat and i dont know how to get that off without burning the wood, maybe some paint stripper will do the job? i shall post some pics to show you how it looks now and hopefully peeps can gimme some pointers BTW:i used to use LOTS of aerosol cans for purposes and i know loads of brands, does any body know if montanas would be good? cheers for all the help!
  14. hey guys, i have a black squire stratocaster that i wanna compltley redo the finish and i have read all of the guides and they have REALLY helped and was wondering if this is the best way of doing stuff: 1)use a paint stripper and apply layers and use a plastic scrapper to remove and do this numerous times 2)use some light sandpaper and sand off the remaining bit of paint until it is just a wood body 3)use a laquor and give the body a couple of coats of it and that is where i get lost????????? i am using poor mans spraypaint and i am using plasticote stuff, what type of aerosol can do i need and do i have to base the body in white primer? sorry for all the questions its because i really wanna get this right cheers guys
×
×
  • Create New...