Jump to content

kczuk

Members
  • Posts

    16
  • Joined

  • Last visited

Everything posted by kczuk

  1. Yes, I'm thinking about which one I want to try. For now, I'm happy it plays haha Absolutely! I'm really happy with the look of the two drastic woods, gives it the raw finish I was hoping for. I picked up some ferrules, they just didn't arrive yet! I like the look better than using a plate (and my screw holes are probably slightly off for a plate). Definitely don't want a split or crack
  2. Alright everyone! The build is COMPLETE. I'm honestly amazed that it plays haha. The bridge is a bit short (or the neck pocket depth isn't deep enough), but luckily it still sets up well when I max out the action on the strings. Feels and sounds great, I'm really stoked on how it turned out. A great memory to have, and now I get to write new music on the actual wood that helped write the old music. Thanks for everyone's help and input, can't wait to work on more builds in the future! Here's a link to a clip of me using it: https://www.instagram.com/p/CZaSkDRlqyA/
  3. Alright I know I haven't been updating a whole lot, but I'm 2 coats of oil into the body and neck! Going great so far. The last key is getting the logo on the headstock, which I've gotten waterslide paper for. Almost there!
  4. Alright, well I was able to round the edges, create the arm and belly cut, and drill the neck pocket holes. Everything went really well actually, except for the fact there's a gap in the neck pocket. I used toothpicks in the pre-drilled neck holes to mark the neck pocket, then I drilled the holes a bit closer to the bridge from there, but apparently it wasn't close enough, as I still have that gap near the heel. I'm not sure if there's a way to fill the space, or if it's a deal breaker in terms of playability. A bit upsetting, but this was probably the toughest part for me, so it didn't turn out too bad. I do still have enough wood to make 2 more bodies, so I can make sure to do better on the next two when I get around to them.
  5. I was able to route the pickup cavities today. Had to create another custom template for them since I didn't have a 7 string one. Overall they turned out pretty well! During the bridge pickup, the set screw on the bearing of the router bit came out without me realizing, so I dug into the template a bit in a few areas (right ear etc), but since I'm using pickup rings it shouldn't be a big deal as they'll be covered. Not upset as it was my first time using the plunge router.
  6. Ah, the issue is that I have a neck from Warmoth that already has pre-drilled screw location for the neck pocket, so I just need to figure out a way how to mark the top of the neck pocket when I have the neck aligned properly. I've thought about putting some small nails inside of the predrilled holes, so I can lay the neck in aligned and then press down to mark the neck pocket with the locations
  7. Alright, I was able to get a lot done on it over the weekend! I built a custom jig for my router to plane two pieces of the wood, and glued them together. Then I was able to route the body and neck pocket as well. The most challenging part was that I had to create a new body and neck pocket template for what I wanted, because it's a 7 string build, and none of the templates that I have worked for the specific dimensions. Once those were made, things went smoother. The only part that I'm a bit bummed about is that the thickness is larger than I intended. The body is about 1.875" thick instead of 1.75", just a mistake when planing and gluing the two pieces initially. As a first build for me, I'm happy I'm able to get it to look alright though. I still have enough wood from the table top to build 2 more bodies, so I can correct it on those next time. Up next I have to figure out how to align and drill out the neck pocket holes for the bolts, route out the pickup cavities, and figure out how to make the arm and belly cuts. Stay tuned!
  8. oooo okay! Great ideas. I'm going to look into printing the decal on some clear waterslide material. Would I still be able to finish the headstock with the oil afterwards, or would you recommend applying the decal at the very end once the headstock is finished?
  9. ALRIGHT. It's been a minute, but I've finally acquired all the things I need (or at least most of them, to start working on the body). I've got a router incoming today with bits, and I'm going build a jig/sled so I can use the router to plane the pieces to the right thickness to combine. A few questions: What would be best to finish the neck with? It's a maple neck from Warmoth I'd like to put a decal on the headstock, what kind of paint would be best for applying that before finishing? What would be best to use to finish the body to keep the "unfinished wood" feel once I sand it down? The only other thing is that the templates I got are for 6 string parts (neck pocket and humbucker templates), so I'll have to mark out the correct sizes and slide them around a bit when using the router.
  10. That's great to hear! I'm looking forward to this not only being something to hang on the wall. It's exciting to think it could be playable, depending on how well my amateur woodworking skills are haha It's starting to feel that way.. I already found myself thinking about doing a strat build for fun. How did I get here already? And that SG looks awesome! I love the accent line in the middle, I'll definitely be trying to keep it with the extra veneer in the center for this build. I'm hoping to order myself a neck and other hardware in upcoming weeks, so I'll keep you guys posted on how this goes!
  11. Good point! If I leave the veneer in the center as an accent, it would look better with the thinner portion on top. I found a buddy with a planer (along with some other tools I'll need), so I think I'll plan to plane both of the 2 pieces on that side before layering them, to make sure they're not uneven. Definitely can't dent it with fingernails. If I push a nail, it only make a small indent on the surface of both side and end grain, I can't get it into the wood with just my hand. I'll check for this! On the piece I cut already, it's extremely solid and the sound is consistent everywhere, which is a good sign.
  12. Ah! So just layer it on itself to use only the desk for the body. I like that idea first before trying to get off the veneer and use it on a different body. Then the surface of the whole body can be that unfinished white feel from the top of the desk! Are there any strength concerns when layering these pieces? Should I keep the thinner of the two layers on the top of the body, or the bottom?
  13. The veneer on the bottom is 2 layers, about 3/16". And the veneer on the top is 1 layer, 1/16" thick. So it looks like I can use either side, but I'll probably have to plane off the inside. I sanded some of the top paint off, and it looks really nice, and I can even keep some of the white in the grain for an unfinished look, which would look really cool. A flat top is alright with me, especially for a first build, haha. I think I'll still do a bevel for the right arm, which will expose the body wood and give it some more character. Now time to select a tonewood and figure out how to apply the veneer well!
  14. Alright @Bizman62, looks like you're right! I'm thinking this might still be able to be used for a top wood though?
  15. Ah, thanks for all the info!! This is very helpful. I'm going to cut a section that could be used for a body, so we can see exactly what it's made of. In the meantime, here's the top and yes, good point. Since it's thinner (and may not even be solid maple), I can use sections as a top wood, which would honestly be just as great. Cross section incoming shortly
  16. Hey all - New here, and I've got some questions about a build idea I have. I have a sentimental piece of wood (hard maple I'm told) that I'm interested in using to create some guitar bodies for some 7 string baritone builds. The wood is from the top of an old desk, which was used to write a record with some buddies. A few questions/considerations that I'd like to get some thoughts on. The piece measures 60" x 32" x 1 1/4". I realize this is a bit thin to work with for body, but might still work with minimal sanding/removal on the thickness. Should I try to make the 1 1/4" thickness work? Or should I layer it to give myself some more space? Bridge will be fixed, and electronics will be minimal, so I don't need too much space in the body for that. I'm hoping to get 2 guitar bodies out if it total (which I think would still work if I need to cut 4 pieces to layer into 2 bodies). I'd like to bolt on a Warmoth 7 string baritone neck, but I'm not sure how to ensure the dimensions would fit perfectly in the pocket. Would the best approach be to order the neck first and measure off of it to create the pocket? Or are there any dimensions available for these necks (I can't seem to find any on their site)? Any other tips or things I should consider when creating this? As this will be my first build, I'm very inexperienced, but hoping to learn a lot from it (and not completely ruin the guitar in the process, haha). There's a few minor holes in the piece, where the drawers and the rest of the desk were attached, but I think they can be avoided, as there's still plenty of space around them. This process is more about having a memento for the record, rather than having a perfectly built guitar, though I'd still like to be able to play it. Thanks!
×
×
  • Create New...