Ibaneznubcake!

cool, thx capu, sorry to be a pain again=D But what type of seal did you use (sanding sealer?) and how many coats? o, and did you use anythink on the maple before to stained it? thankyou.

i have a question. very nice guitar btw. can you pm me and take my though the steps of staining it ect:? i need to know how you got that cool look on the body^^

transparent blue? is that diffrent from dye/stain? carn't i dye is blue like the Quilted and then clear coat is? to give the same affect?

Does the same staining apply to this one too? and what type of dye do i need to use water base ones?, or spirit? and again whats the diffrence between dye and stain...

someone..please...:/

I am not sure where to put this so i will put it here:) Anyway! I'm wondering How do i get this look on a guitar body. I know that 1. I need a nice grained body/Laminate Top /QUILTED affect on it for starters. But if i use spray paint wount it cover up the grain? What type of paint..or even oil do i need to show that affect? & whats the diffrence between staining, and dyeing a top?

So i went up to the town today and got the stuff i need to Test the Swirling Oil paint from the local model shop and borax from Boots colours i got was black blue green My first go at it did not go too good i put the paint in black blue green and the green had been got flooded by the other colours (mainley blue) there was no green in site:S 2 go. went a little better as for i did not as much borax as i did last time very little lol^^ this time cuz it was only a small bucket. I did not bother with the green I put in the black then the Blue the black went across all over the surface then the blue in lumps. to i tested with my peice of skirting lol^__^ no undercoating turn out like this. 3 go. went the same but with a white undercoating. swirl kinda came out shity the little blobs showing the white coat all over it>.< 4th n 5th i got hold of some red(yays) so i put in black blue red for some reson my red ate the blue....0_o.. its drying at the min so i got no pics sorryS! now here are the questions=D 1# how much paint should i put in?? 2# how much borax should i put in?? 3# why did my "3 go" with the undercoat came out with the shity white spots 4#why do some paint kind dont work (like the green and "red and blue") thx.

once i got my guitar body sanded down. should i use a white under coat then spray paint it blue then dip it? trying to get the same affect as blackknight or like in the vid was it a green under coat? thx.

as long as its for personal use and your not going to make them and sell them thats ok. but if u gte tired of it make sure you sell it to someone you know. not on evilbay or anythink like that.

how often should i clean the finger borad? (not the frets) thx. -Ibanezn00b

right..ermm ok how about if i just buy a normal neck from here http://www.axesrus.com/axenecks.htm the high nitro gloss and leave the neck blank. would it be ok then? or would i have to get the mighty mite (cuz thats reg by frender anyways)

iam kinda confused., so i can make a strat looking guitar as long as i dont put any kind of fender logos on it. sell it as long as i state thats its not by fender? right?

cool thx! do they ship to the UK?, or do you know any other site from the uk? thx!

cool thx! Do you know if they send to the UK? or have any UK sites like this ty!

bump! GOOD NEWS! -update Just buyed a body of evilbay for £30 its hardwood Alder. So its a bit better than ply/chip/ or bass =) downside is that I could only get the guy the guy to gimmy a trem system with it. It was that or some pickups and a scrathplate... And the pickups up could have been crap...so ye anyway! So post ya ideas here for it. I'm gona try to keep it to a small buget since its my first. maybe not the best pickups but not the worst maple neck- mighty mite w/e its called then need to find out how to do the wireing ect: 0.0!!!!! ooo god =( lol much thankies! -Ibaneznub