shad peters Posted January 9, 2012 Report Share Posted January 9, 2012 Offset Avenger: This guitar is based off my avenger design, but as you might have guessed, its an offset version to make it a little more comfortable to play while sitting. specs: carved top neck-thru design with a 5-ply of curly maple and walnut for the core alder body wings a walnut burl top full round edges contoured heal volute at the headstock walnut veneer on both sides of the headstock ebony fretboard with split block inlays and creme binding sperzel tuners bone nut gotoh bridge and tailpiece seymor duncan jb/jazz in the bridge an neck position. Electronics: master volume/ pushpull for neck out of phase bridge tone/ pushpull for bridge coil split neck tone/ pushpull for neck coil split blend pot DPDT as a series parallel switch avenger (30) by Peters Instruments, on Flickr avenger (2) by Peters Instruments, on Flickr avenger by Peters Instruments, on Flickr avenger (8) by Peters Instruments, on Flickr more photo's here http://www.flickr.com/photos/petersinstruments/ Link to comment Share on other sites More sharing options...
Bukoffsky Posted January 11, 2012 Report Share Posted January 11, 2012 (edited) Bukoffsky Black Beauty aka Bozidar Radenkovic Signature This is my second build. Guitar was made for a friend who is a regular gig musician playing jazz/rock/folk..... Black stain over beechwood, and oil finish all around. MORE PICS: Beechwood body Ash neck Ebony Fingerboard Gibson Scale Gotoh Tuners Gotoh TOM and Stoptail Golden Age PAF Humbuckers (split coiled and potted) Three way switch, Split coils Mud switch Edited January 11, 2012 by Bukoffsky Link to comment Share on other sites More sharing options...
factory5150 Posted January 13, 2012 Report Share Posted January 13, 2012 Here is one I completed last month. I call it Precious Moment It was based off of Joe Perry's white guitar. It is a solid body ES-335. Here are the specs: Body: 1 piece African Mahogany with Maple cap. Neck: 4A flame Maple with flame Maple fretboard Inlay: Tree of life - faux Turquoise for the big leafs, abalone shell for the small leafs, and Indian Rosewood for the stem. Turquoise and Abalone for my logo. Hardware: Gotoh tuners, bridge and tailpiece. Scale: 24 3/4 Pickups: EMG 81/85, standard vol and tone with 3 way switch. Paint: I did the base white and clear in 2k urethane, but the airbrushing was done by Mad Momma Designs out of Pittsburgh. The neck was finished with TruOil and waxed. Sorry I don't have a full guitar picture, my photographer hasn't sent me one yet. More pictures here: http://www.flickr.com/photos/47467970@N05/ Hope you all enjoy it! Link to comment Share on other sites More sharing options...
Our Souls inc. Posted January 13, 2012 Report Share Posted January 13, 2012 The Comicaster , a pine bodied Tele-style with a super-theme. Specs: Pine Telecaster body Super-Hero poster graphics Faux- chrome trim on the edges 25.5" scale , 22 frets Guitarheads Tele pickup set here are some pics: build thread here : http://projectguitar.ibforums.com/index.php?showtopic=43080&st=0&p=457916&hl= Link to comment Share on other sites More sharing options...
orgmorg Posted January 16, 2012 Report Share Posted January 16, 2012 Victorian Muleskinner This ended up being sort of a cowboy steampunk kinda thing. The top is a piece of beech barn siding, sanded down just past the grey weathering. The back is yellow poplar, and chambered so there is open space behind the knot hole. Neck is black walnut and beech, with a persimmon fretboard. Bridge pickup is Motor City Afwayu, with an Amalfitano tele neck pickup. An unlikely combination for sure, but was specifically requested by the customer who likes to be able to go from High gain crunch to super clean prettiness. This definitely does that, but apparently requires some fancy footwork. The bridge is a basic hardtail affair I made from brass with compensated tele saddles, and covered with an antique cast iron drawer pull. The control plate is also victorian era, a copper plated doorknob backplate. Very simple controls, which gave me a chance to use this big old cool knob which I only had one of, and is almost doorknob size. Pickguard is rusted roof tin laminated to bakelite sheet. More pictures~ Headstock Back of headstock detail other side back Link to comment Share on other sites More sharing options...
demonx Posted January 18, 2012 Report Share Posted January 18, 2012 Searls Guitars - SUPERSTRAT - 7 string Mahogany body 3 piece Maple Neckthru Ebony board with white binding Rosewood stringers 25.5" scale 6150 Jim Dunlop fretwire Compound radius starting at 16" Mother of Pearl large diamond inlays Reverse Sasafrass headstock Kahler Trem Grover Mini Tuners Bridge p/up - Bareknuckle Painkiller Neck p/up - Custom order Bareknuckle single Switchcraft selector CTS pots Oil paper cap 0.022uf 2k automotive finish Build Thread: http://projectguitar.ibforums.com/index.php?showtopic=45901 Link to comment Share on other sites More sharing options...
Boggs Posted January 21, 2012 Report Share Posted January 21, 2012 Lefty Cicada by RockBeach Guitars Koa and Tulip Poplar body Birdseye Maple neck with Pistachio fingerboard and medium jumbo frets 25" scale length Texas Special pickups GraphTech ResoMax Bridge Hipshot Tuning Machines Murdoch Hard Oil Finish Link to comment Share on other sites More sharing options...
ProjectGuitar.com Posted January 25, 2012 Author Report Share Posted January 25, 2012 Time to vote click here Link to comment Share on other sites More sharing options...
Recommended Posts