Jump to content
Entry in the May 2024 Guitar of the Month contest is now open ×

Scott Rosenberger

Blues Tribute Group
 View Profile  See their activity

  • Posts

    2,782

  • Joined

  • Last visited

 Content Type 

Everything posted by Scott Rosenberger

  1. Scott Rosenberger
    Alder sometimes has very small knots which usually aren't a problem, I would fill the grain personally because after a while the finish tends to settle into the grain of Alder Bodied Guitars
  2. Scott Rosenberger
    There was one in the downloads section but now you have to make a donation to Project Guitar to get access to it
  3. Scott Rosenberger
    Same here, occasionally I have a neck that needs a little attention after fretting but not very often, and I fret about 6-10 necks a weeks on average
  4. Scott Rosenberger
    Sperzel Locking Tuners can be assembled either way, just buy a 6pack of inline and take two apart and reverse them
  5. Scott Rosenberger
    Horns Section??? What is this? the Blues Brothers
  6. Scott Rosenberger
    I just trim the whole thing off and use a Floyd Nut shim to get the nut set right,
  7. Scott Rosenberger
    you could put a slightly larger bearing on your router bit which would make the neck pocket smaller
  8. Scott Rosenberger
    you can get an inexpensive Hygrometer? sp? at your local wood supplier or online. check your wood first then decide if it needs to be taken inside to dry more or not
  9. Scott Rosenberger
    I dont think it's Blue enough for Simon
  10. Scott Rosenberger
    Pull the fretboard yourself it's easy, just use the tutorial on the site and take your time it only should take you about an hour or so
  11. Scott Rosenberger
    This comment was a faux paux in the Ibanez catalogue's, the 7620 didn't have dimarzio blaze pickups in it, it has the standard Ibanez 7 pickups in it that the 7420 was supposed to have. there were a couple different versions of each, but a phone call with hoshino told me that the RG7's never came with dimarzio's in them. Just a little FYI based on what I was told. (which could still be wrong ) The pickups in my 7620 are Dimarzios, The say so on the bottom
  12. Scott Rosenberger
    It's good practice for your finishing skills regardless of whether or not the glue joint holds. Finish it and if it cracks later, then get a new body
  13. Scott Rosenberger
    Here
  14. Scott Rosenberger
    Pull the neck and see if it has a shim in the neck pocket
  15. Scott Rosenberger
    check ebay you can probably get a Schaller Stop tailpiece for like $30
  16. Scott Rosenberger
    WD Bridge
  17. Scott Rosenberger
    try calling PRS or contacting a PRS Dealer
  18. Scott Rosenberger
    I t sounds like it could have happened when you were re-raduising the fretboard by not sanding parallel to the fingerboard. If you pull all the frets and fix the board you probably have to re-saw the fret slots. If it's not "twisted" too bad you could even correct it with a dressing of the frets
  19. Scott Rosenberger
    Carvin uses them on their guitars Try Here
  20. Scott Rosenberger
    a Wilkenson would be a good bet because only the post on the top of the body needs to be exact, the bottom post can go anywhere along the body of the trem
  21. Scott Rosenberger
    I see an Eerie Dess Swirl in someone's future
  22. Scott Rosenberger
    yeah you just treat the acrylic just like paint an d keep sanding with finer and finer grits until you get to about 3000 then polish, just be prepared, the scratches are alot harder to remove from plexi than paint
  23. Scott Rosenberger
    it will probably sound like crap, there's so much glue holding all that sawdust together it wont vibrate
  24. Scott Rosenberger
    Kramer used aluminum necks on their early guitars
  25. Scott Rosenberger
    ok I'll bite, I'll swap the one in mt RG 7620
×
×
  • Create New...